Verilink PRISM 3010 (CG) Configuration/Installation Guide Manuale Utente Scaricare il pdf (Pagina 2)

Port Configuration Menu

The Voice Card Configuration screen display allows the assignment of voice DS0s

to network channels. This display is accessible from the PRISM unit front panel

LCD, its terminal interface, or the 8100A Site Controller under the Configuration

top level menu. Only the voice ports with the Mode parameter set to ACTIVE are

connected to the selected network channel.

The 3010 voice modules have six voice circuits, each of which is independently

assignable to a selected network channel. For a more detailed description of voice

port operation, refer to the reference manual for the product where the card is

located. The following fields are available for voice port configuration:

Port: This field indicates the port number of the card in the assigned slot.

DS0: This field assigns the voice port to a network channel. The choices are

channels 1 through 24.

Mode: This field selects whether the voice port is actively assigned to a network

channel, ACTIVE, or is not used, SPARE. If set to SPARE, the other voice port

parameters are ignored and the port is inactive.

State: This field displays the voice port status as either in the BUSY or IDLE state.

Name: This field may be used to provide up to 20 characters of text for identify-

ing the voice circuit name and number.

Signalling: This field selects the supervisory operation of the voice port. The

choices for the different modules are as follows.

FXS

• FXS/LS Foreign Exchange Station / Loop Start

• FXS/GS Foreign Exchange Station / Ground Start

• MEG/LS MEGACOM

/ Loop Start

• MEG/GS MEGACOM / Ground Start

• PLAR Private Line Automatic Ringdown

• DID/DNIS Direct Inward Dialing/Dialed Number Identification

Service [Dial Pulse Originate (DPO) mode]

• DNISW/LS Loop Start DNIS (LS-DNIS) with wink

• DNISD/LS LS-DNIS with delay start

• DNISWR/LS LS-DNIS with wink and Reverse Battery

• DNISDR/LS LS-DNIS with delay and Reverse Battery

• DNISW/GS Ground Start DNIS (GS-DNIS) with wink

• DNISD/GS GS-DNIS with delay start

• DNISWR/GS GS-DNIS with wink and Reverse Battery

• DNISDR/GS GS-DNIS with delay and Reverse Battery

FXO

• FXO/LS Foreign Exchange Station / Loop Start

• FXO/GS Foreign Exchange Station / Ground Start

• FXO UVG Foreign Exchange Office/Universal Voice Grade

• FXO UVGR Foreign Exchange Office/Universal Voice Grade

with Reverse Battery

• DID/DNIS Direct Inward Dialing/Dialed Number Identification

Service [Dial Pulse Terminate (DPT) mode]

4-Wire E&M F-3010-200--112

F-3010-200--114

• Type I Signalling YES YES

• Type II Signalling YES YES

• Type III Signalling YES YES

• Type IV and V Signalling NO YES

• TO Transmission Only YES YES

Delay Seconds: If the signalling mode has a delay, it can be set from 1 to 5 seconds.

Tx Gain: This field selects the transmit gain over the following ranges:

2-Wire FXS: -4.0 dB fixed

2-Wire FXO: -6 dB to 0 dB

4-Wire E&M: -10 dB to +3 dB, 0 dB

Rx Gain: This field selects the receive gain over the following ranges:

2-Wire FXS: -11 dB to 0 dB

2-Wire FXO: -6 dB

to 0 dB

4-Wire E&M: -16 dB to +2 dB, 0 dB

Slot/Channel Allocation: These display-only fields indicate the network chan-

nel assignments with Channel 1 on the left and Channel 24 on the right. The upper

line indicates the card slot to which the channel is allocated. The lower line indi-

cates the port in the assigned card for that channel.

2-Wire FXS Screen

3060 DSU Time: HH:MM:SS

Element Rev xx.xx/x.xx Date: MM/DD/YY

--------------------- VOICE CARD CONFIGURATION -------------------

Slot: (2)

Card Type: 2 Wire FXS

Delay Tx Gn Rx Gn

Port DS0 Mode State Name/ID Sig. Secs. dB dB

------------------------------------------------------------------

A ( 1) [ACTIVE] BUSY ( ) [FXS/LS] (-4.0) ( -2)

B ( 2) [ACTIVE] IDLE ( ) [FXS/GS] (-4.0) ( -2)

C ( 3) [ACTIVE] BUSY ( ) [MEG/LS] (-4.0) ( -2)

D ( 4) [SPARE ] IDLE ( ) [MEG/GS] (-4.0) ( -2)

E ( 5) [SPARE ] IDLE ( ) [PLAR ] (-4.0) ( -2)

F ( 6) [ACTIVE] BUSY ( ) [FXS/LS] (-4.0) ( -2)

222222 333333 ------ ------

Channel Allocation: ABCDEF AAAAAA ------ ------

---------------------------- Messages ----------------------------

2-Wire FXO Screen

4-Wire E&M Screen

MEGACOM is a registered trademark of AT&T.

3060 DSU Time: HH:MM:SS

Element Rev xx.xx/x.xx Date: MM/DD/YY

--------------------- VOICE CARD CONFIGURATION -------------------

Slot: (2)

Card Type: 2 Wire FXO

Delay Tx Gn Rx Gn

Port DS0 Mode State Name/ID Sig. Secs. dB dB

------------------------------------------------------------------

A ( 1) [ACTIVE] BUSY ( ) [FXS/LS] ( -6) ( -2)

B ( 2) [ACTIVE] IDLE ( ) [FXS/GS] ( -6) ( -2)

C ( 3) [ACTIVE] BUSY ( ) [MEG/LS] ( -6) ( -2)

D ( 4) [SPARE ] IDLE ( ) [MEG/GS] ( -6) ( -2)

E ( 5) [SPARE ] IDLE ( ) [FXO/GS] ( -6) ( -2)

F ( 6) [ACTIVE] BUSY ( ) [FXO/LS] ( -6) ( -2)

222222 333333 ------ ------

Channel Allocation: ABCDEF AAAAAA ------ ------

---------------------------- Messages ----------------------------

3060 DSU Time: HH:MM:SS

Element Rev xx.xx/x.xx Date: MM/DD/YY

--------------------- VOICE CARD CONFIGURATION -------------------

Slot: (2)

Card Type: 4 Wire E&M

Delay Tx Gn Rx Gn

Port DS0 Mode State Name/ID Sig. Secs. dB dB

------------------------------------------------------------------

A ( 1) [ACTIVE] BUSY ( ) [TYPE 1] (-.5) ( +2)

B ( 2) [ACTIVE] IDLE ( ) [TYPE 3] (-.5) ( +2)

C ( 3) [ACTIVE] BUSY ( ) [TYPE 2] (-.5) ( +2)

D ( 4) [SPARE ] IDLE ( ) [TO ] (-.5) ( +2)

E ( 5) [SPARE ] IDLE ( ) [TYPE 1] (-.5) ( +2)

F ( 6) [ACTIVE] BUSY ( ) [TYPE 1] (-.5) ( +2)

222222 333333 ------ ------

Channel Allocation: ABCDEF AAAAAA ------ ------

---------------------------- Messages ----------------------------

Sales and Marketing

800-285-2755

256-772-3770

info@verilink.com

Technical Support

800-285-2755

256-772-3770

support@verilink.com

Returns/RMA

800-285-2755, ext. 2282

127 Jetplex Circle

Madison, Alabama 35758

www.verilink.com

1 2

Commenti su questo manuale

Nessun commento

Verilink PRISM 3010 (CG) Configuration/Installation Guide Manuale Utente Pagina 2

Commenti su questo manuale

Prodotti e manuali riguardandi Hardware del computer Verilink PRISM 3010 (CG) Configuration/Installation Guide